mikroUši
- Stereo-matched pair with consistent response
- Ultra-compact 6.8 mm diameter for nearly invisible placement
- Modular cable system for maximum flexibility
- Plug-in powered (2–10 V)
- Low self-noise (~20 dBA)
- High sensitivity (−32 dB re 1 V/Pa)
| Parameter | Value |
|---|---|
| Transduction principle | Pre-polarized condenser (electret) |
| Directional characteristic | Omnidirectional |
| Sensitivity (free field, 1 kHz) | −32 dB re 1 V/Pa (≈25 mV/Pa) at 1 kHz, ±3 dB (unit-to-unit) |
| Equivalent noise level (A-weighted) | ~20 dBA |
| Maximum input SPL | ~115 dB |
| Power supply | 2–10 V plug-in power |
| Rated output impedance | 1.6 kΩ ±30% |
| Minimum load impedance | 16 kΩ |
| Output connector | 3.5 mm jack |
| Output type | Unbalanced |
| Dimensions | 8.5 mm × ⌀6.8 mm |
| Cable length | 1.5 m per microphone |
| Cable diameter | 2.1 mm |
| Operating temperature | −10 °C to +55 °C |
| Storage temperature | −25 °C to +70 °C |
Read this before first use
- Never open or disassemble the microphone. There are no user-serviceable parts inside, and opening it voids the warranty.
- Protect the microphone from water and moisture. It is not waterproof. If it gets damp, let it dry fully at room temperature before using it again.
- Keep dust out. Store the microphones in a closed case or pouch when not in use — dust combined with humidity can cause crackling noises that require factory cleaning.
- Mind the temperature. Operate only between −10 °C and +55 °C, and don't leave the microphone in direct sun or a parked car.
- Protect your hearing. When monitoring on headphones, start at low volume and raise it gradually — unexpected loud sounds can occur at high gain.
Use only LOM cables
Never use third-party mini-XLR cables with mikroUši. LOM cables contain circuitry that adapts the recorder's voltage to the capsules — connecting a plain cable to a powered input may permanently damage the microphones, and such damage is not covered by the warranty.
Will it work with my recorder?
mikroUši needs a 3.5 mm stereo microphone input that provides plug-in power (2–10 V). Practically every dedicated field recorder has one — though on some, plug-in power must be enabled in a menu first. Smartphone and laptop headset sockets use different wiring (TRRS, mono mic) and are not directly compatible. If your recorder only has XLR inputs, use the Uši phantom adapter or swap to the Uši Pro (XLR) cable.
Quick start
- Connect each microphone to the Uši (minijack) cable — push the mini-XLR connector on until it clicks.
- The cable branch with the red ring is the right channel. Position the microphones — for a natural stereo image, space them roughly head-width apart (15–20 cm), or clip them to your shoulders or hat brim for a wearable, binaural-style rig.
- Plug the minijack into your recorder's 3.5 mm mic input and make sure plug-in power is on (check your recorder's manual).
- Put on headphones and set the gain: start low, then raise it until the loudest sounds you expect peak around −12 dB. Gently rub a finger near each capsule to confirm both channels are live.
- Make a short test recording and listen back before the real take.
Using the included mikroUši clip
The mikroUši clip is designed to be used together with wind protection: insert the microphone cable into the groove, then gently pull the microphone into the designated "cup". See more mounting ideas.
Using the wind protection — mikroUši windbubbles (optional accessory)
For outdoor recording, slip a windbubble over each capsule to reduce wind noise. Match the size to the microphone — see recommended wind protection.
Swapping cables
The system is fully modular: mikroUši capsules also work with the Uši Pro (XLR) cable for phantom-powered recorders. Use only LOM cables (see the safety notes above).
Disconnecting the capsules from the cable
Press the button on the mini-XLR connector and pull the capsule straight off. If you can't get the connector off, try this.
mikroUši is the choice when the microphone must disappear: covert and discreet field recording, location sound on actors and instruments, tight spaces where nothing larger fits, and wearable stereo rigs. The tiny capsule keeps its response far beyond the audible range (up to ~80 kHz), making it a favorite for recording ultrasound — bats, electronics, rodents. For very quiet nature ambiences, the larger Uši has a lower noise floor (~14 vs ~20 dBA); sources above ~115 dB SPL will overload the capsule — see the comparison table.
Storage. Keep the microphones in a closed case or pouch, away from dust and humidity. Coil the cables loosely — sharp bends shorten their life.
Cleaning. Wipe the body with a dry or slightly damp cloth. Never use solvents or compressed air, and never poke anything into the capsule openings. If a connector gets dirty, wipe the contacts with a dry cloth.
Condensation. When you bring the microphones from cold outdoor air into a warm room, moisture can condense inside the capsules and cause crackling or popping sounds. This is not a fault — let them acclimatize for 30–60 minutes and the noise will disappear on its own. If crackling persists in normal conditions, contact us rather than attempting to clean the capsule yourself.
Dusty or dirty environments. Use wind protection even indoors when recording in dusty places — it keeps particles out of the capsule.
- No sound, or a very quiet signal → is plug-in power enabled, and are you in a mic (not line) input? See no signal.
- Only one channel records → check both mini-XLR connectors are clicked in and the recorder isn't set to mono. See one channel silent.
- Crackling or popping → most often condensation after a temperature change. See crackling and popping.
- Distortion on loud sources → lower the gain; above ~115 dB SPL the capsule itself overloads. See distortion.
- The cable won't come off → don't force it — see the technique.
Manual PDF download coming soon
Warranty. LOM products are covered by a two-year guarantee beginning on the date of purchase. Keep your proof of purchase — it is required for any claim. Within the guarantee period we will, at our discretion, repair or replace products with defects in materials or workmanship. The guarantee does not cover damage caused by misuse, mechanical damage, moisture, unauthorized modification, or use with third-party cables or power sources outside the published specifications. Destructive opening of certain parts of the product voids the warranty.
Repairs. Before sending anything back, contact us with a description of the problem and your proof of purchase — many issues can be resolved without shipping.
Declaration of conformity. This product complies with the applicable European directives, including EMC Directive 2014/30/EU, when used with cables and accessories supplied by LOM.
Disposal. Do not dispose of the product in household waste. Like all electrical and electronic equipment, it must be handed in at a WEEE collection point at the end of its life.
Manufacturer: LOM s.r.o., Jelenia 10, 811 05 Bratislava, Slovakia · store.lom.audio